P 323 - Laser beam welding of lightweight wheels made from DP600 steel

P 321: Determination of the decisive static and dynamic wind load distribution on steel hall structures using the plastic load-bearing behaviour The design of load-bearing structures in civil engineering is based on the limit load under maximum possible stresses. With regard to the actions to be applied, e.g. due to weather events, certain standard values are used in the calculation. The decisive wind load to be applied here is currently still based on elastic load-bearing behaviour. However, modern regulations allow the design on the plasticised system, which results in a redistribution of the internal forces compared to the elastic calculation. For the plastic design, no wind load relevant to the design can be taken from the current standards. This is where the research objective of the project comes in: By investigating in particular the interaction between the time course of the wind effects and the elastic-plastic structural reactions of hall buildings of standard dimensions, realistic failure limits were to be determined in order to improve the accuracy of the design. The time histories of the wind pressure distributions on the windward, leeward and roof sides were determined in a wind tunnel using models of hall structures. From this, the static and dynamic reactions of a hall frame up to failure were determined in time step calculations. Excessive lateral deformations or material fatigue due to repeated plastic deformations were used as failure criteria. The results show that the previous designs are on the safe side if only the wind load assumptions (see EUROCODE 1 - Part 2.4) are used. The load redistributions in the steel structures form a load reserve of up to 9 %. However, if one assumes the combination factors for wind plus snow, then the load reserve is even higher due to a reduction in the load assumptions, and thus a change in the standard (EUROCODE 1 - Part 2.3 Snow / 2.4 Wind) is indicated. It has also been shown that no increase in safety factors is necessary due to allegedly insufficient reserves in light steel structures. A comparison of these results with an evaluation of data from the German Weather Service on the probability of the interaction of snow and wind for a few locations and examples showed that excessive combination coefficients had always been calculated. Further investigations are currently underway to determine the general validity of these findings. An adaptation of the calculation to the real effects of the load combinations will lead to more economical load-bearing structures. STUDIENGESELLSCHAFT STAHLANWENDUNG e.V. Publication: 1999 Authors: Prof. Dr.-lng. G. Sedlacek, Dr.-Ing. W. Zillinger, Dipl.-Ing. O. Krau

P 327 - Comparative assessment of the fire behaviour of different structural steels to determine fire-resistant steel structures without additional fire protection measures Authors: G. Sedlacek, C. Heinemeyer Publication: 2003 The choice of the material for structural elements between e.g. steel, wood or concrete depends on the experiences of the designer with the specific material and planning reliability that can be achieved in early design stages of the project. On aspect for choice of materials is fire safety. Therefore it is usually proved if the structural element fulfils general requirements given by codes or other regulations. These general requirements give classifications for the performance of structural members under ISO-fire condition. The lowest level of load bearing classification under ISO-fire can in most cases on be achieved by using protections systems for the structural elements. The use of protection systems such as coating or cladding of the elements leads to uneconomic solutions for steel structures and architectural design aspects cannot be fulfilled. One possibility to realize fire safe, economic and unprotected steel structures is the global fire safety design which considers realistic fires (Natural fires) and which allows to estimate the load bearing resistance under these fire conditions. (Visible steel by invisible protection measures.) To perform global fire safety design all influences on the definition of a fire have to be known. This is a disadvantage of this design procedure because all these influences are not surely known until a later design stage of the project is reached.

P 328: Characterisation of the material properties of steel after hydrostatic stretch forming Forming with hydraulic active media is still a relatively uncommon innovative processing method for steel. To date, there is no general test method tailored to these special forming conditions for determining material suitability. The aim of the project was therefore to investigate the behaviour of various ferritic and austenitic steels under the conditions of hydrostatic forming into bump plates and the subsequent characterisation of the material properties. The information gained from this is to be used to develop a suitable method for determining material suitability and formability limits. The tests were carried out on the ferritic deep-drawing steels St 14, StE 180BH and DB 500 as well as on the austenitic steels 1.4318 and 1.4301. For the tests, bumps were stamped onto sheets with a thickness of 0.5 to 1.25 mm using hydrostatic stretch forming in a two-stage process. The forming result was analysed with regard to thickness change and hardness progression as well as metallurgically. In parallel, comparative computer simulations were carried out to analyse and explain the forming results. The findings were compared with the results of supplementary bulge tests. The investigations have shown that the wall thickness distribution of the deformed sheets can be predicted with the aid of the forming limits and the use of a simulation programme. The test results provide information on the manufacturability of products of any geometry by means of forming with hydraulic moulding media. Based on the direct correlation between the degree of forming and hardness, the hardening at any point of a planned product can be predicted. The research results show that the selected forming process to form cusps is not suitable as a general test method. In contrast, an appropriately modified bulge test probably offers good conditions for the forming behaviour in relation to hydraulic active media. STUDIENGESELLSCHAFT STAHLANWENDUNG e.V. Publication: 1996 Authors: Dipl.-Ing. W. Bausch, Prof. Dr.-Ing. H. Nowack