P 1379 - Determination of forming limit curves at elevated temperatures

P 1374 - Ultrasonic-assisted machining of hybrid materials As part of the European joint research project, the project consortium consisting of the Fraunhofer Institute for Machine Tools and Forming Technology IWU together with the Fraunhofer Institute for Process Engineering and Packaging IVV as well as Politechnika Wrocławska (PWr) and the Belgian Welding Institute (BWI) researched innovative methods for ultrasonically assisted joining of metal-plastic composites (MCP). The MCPs investigated as part of the research project consist of two metallic cover layers and a polymer core layer. This class of materials plays an important role in lightweight construction products. Due to their excellent specific stiffness, good thermal insulation properties and high acoustic damping capacity, they offer a high substitution potential for monolithic metallic materials. The joining of MFAs to metallic structures represents a major challenge. Due to the specific properties of the MFAs, the use of conventional joining techniques (e.g. spot welding, clinching or semi-tubular riveting) is limited or only possible with increased technical effort. The main objective of HybriSonic was to apply adapted and improved conventional joining technologies to MKV without a significant increase in process time or deterioration in joint quality. The basic approach is the localised melting of the polymer layer by ultrasonic waves and the displacement of the molten material by pressure on the cover sheets. Two different strategies were investigated for this purpose. In the first approach (one-step approach), the joining tool is directly superimposed by ultrasonic waves and the polymer layer is melted during the joining process and displaced from the joining zone. This approach was used for clinching and resistance spot welding. In processes such as semi-tubular self-pierce riveting or friction stir spot welding, the joining tool cannot be used to couple the ultrasonic waves into the MKV. A second, two-stage approach was investigated for these joining processes. Here, the polymer layer in the joining area is displaced in an upstream process step of sheet metal forming. The MKVs can then be joined as monolithic materials. The investigated approaches were validated for a large number of representative industrial material combinations and products and the advantages and limitations of the technology were recorded. Systematic and objective findings were obtained on the applicability of these novel joining concepts for industrial applications. Publication: 2022 Authors: Prof. Dr.-Ing. W.-G. Drossel, Prof. Dr.-Ing. J.-P. Majschak

Cutting is an essential part in the production of parts and components in most industrial sectors. Nearly every part made from sheet material runs through several cutting steps. Especially shear cutting is very common for mass production in the industry due to its very high efficiency compared to other methods like laser cutting or water jet cutting. However, the increasing requirements concerning cutting of high strength sheet materials (e.g. high strength steel or fiber-reinforced materials) are pushing the shear cutting method to their limits. The main problem is insufficient lifetime of the blanking tools for cutting of high demanding materials. An increase in hardness and compression strength of the tool materials comes along with a decreasing fracture toughness. Early tool breakage or break out of the cutting edges are the limiting factor for cutting high strength materials. New highly efficient shear cutting methods like high-speed impact cutting (HSIC) cannot be used in the industry due to the limitations of the common tool materials. There is a huge demand to overcome the problem of early tool breakage in demanding cutting operations by strengthening the tool materials. In the CORNET-Project InFiBlank (14th Call) the lifetime of a highly loaded fine blanking tools made from high alloyed tool steels could be more than doubled by deep cryogenic treatment (DCT) of the tool material. Especially the break out of the cutting edges was significantly reduced. This approach was combined in this project with adepted diffusion treatments and coatings. Main target of the project was a significant increase of tool life for cutting high strength materials (high strength steels, fiber-reinforced composites) and for HSIC. Objectives in detail have been:  Optimization and integration of DCT treatment in the production process of the tools  Combination of DCT with plasma nitriding treatments and coatings  Proof of concept for blanking of high-strength materials (steel, fiber-reinforced composites)  Proof of suitability for HSIC to prevent early tool breakage  Validation of the concept in different industrial applications  Formulation of a treatment recommendation for the cutting tools Summary Results: Different process routes were compared for DCT treatment, differing in the timing of DCT treatment and cooling curves. Effects on material properties could be achieved with all process routes. Depending on the material and the time of DCT treatment, different effects can occur. The positive effect of DCT treatment on the wear behavior and service life of cutting tools has been confirmed for cutting high strength steel and HSIC on laboratory scale and in different industrial applications. The economic benefit for the different cutting processes depends on the type of tool load and the resulting wear mechanisms. Positive effects can be achieved especially when cutting edge chipping due to fatigue effects and cracking are the limiting wear mechanisms. In this case, a DCT treatment can significantly increase the tool life. Plasma nitriding of the tools turned out to be another highly effective measure for reducing cutting edge chipping and crack formation in the cutting tools. A precondition for this is the use of nitriding parameters adapted to the tool materials and the load situation of the tools. These were developed within the project. The aim of the research project were achieved. Published in: 2026 Authors: M. Demmler, M. Weber, G. Claus

P 1315 - Control of heat input during GMAW thick-wire welding using the example of fine-grain structural steels GMAW thick-wire welding with wire diameters up to d = 4.0 mm is a promising high-performance welding process which, however, has not yet enabled reproducible and economical joint welding of long weld seams. The applicability of the high-performance welding process in the area of temperature-sensitive, high-strength fine-grain structural steels was also previously unknown. In the research project, the new welding process was analysed and validated with regard to its suitability for the material-specific processing of fine-grain structural steels in the thick plate range (t ? 10 mm). The base material S690Q (1.8931) was used as the reference material for the group of high-strength fine-grain structural steels within the process qualification. In preliminary tests, a thermophysical material characterisation was carried out on a dilatometer, whereby the critical limit ranges of the cooling times t8/5 were defined and confirmed (5 s ? t8/5 ? 15 s). Within the project, systematic welding tests were carried out to analyse the influence of different wire diameters on the welding behaviour and the welding result at the upper technical test limit for MSG thick-wire welding. Solid wires of type G69 with diameters of d = 2.4; 3.0; 3.2 and 4.0 mm were used for this purpose. The solutions for controlling the energy input into the base material were aimed at extending the determined technical test limit in the upper performance range. For example, upstream wire heating, which was achieved by increasing the contact tube spacing (?s = 30 mm), resulted in a reduction in the absolute welding power requirement of up to 20 %. With the solid wire, deposition rates of approximately MR = 20 kg/h could be achieved. This corresponded to an increase in deposition rate of approx. 30 %. Furthermore, the use of a basic cored wire with a diameter of d = 3.0 mm had a positive effect on the welding behaviour and allowed deposition rates of up to approx. MR = 30 kg/h to be achieved. A separate cold wire feed into the melt during the welding process made it possible to increase the deposition rate of the thick wire process by up to 60 %. Alternatively, significantly reduced cooling times t8/5 could be realised with the help of targeted process adaptation: - Use of cored wire - 35 % - Increased contact tube spacing - 25 - Cold wire feed - 10 % In addition to the direct control of the energy and heat input into the base material, this made it possible to increase economic efficiency by increasing the deposition rate during GMAW thick-wire welding. With the process combination of cored wire, increased contact tube spacing and cold wire feed, maximum deposition rates of approx. MR = 45 kg/h were achieved in the project, which represents the current maximum value for GMAW thick wire welding. The pulsed and alternating current technologies were not considered to be effective in terms of reducing the energy input for the GMAW thick-wire welding process. In comparison with submerged arc welding, the potential of GMAW thick-wire welding was determined with regard to welding parameters and economic parameters, as well as mechanical-technological quality values for joint welds of fine-grain structural steels. Here, t = 20 mm thick sheets of grade S690Q were welded together in only 70 % of the time and with 60 % of the total costs of the submerged arc welding process using GMAW thick wire welding, while saving on powder costs and powder handling. In addition, MSG thick-wire welding enables joint welds up to t = 25 mm with just two welding beads. The process qualification (tensile tests, hardness measurements, notch impact tests and bending tests) did not result in any negative impairment of the mechanical-technological quality values of the high-strength fine-grain structural steel (S690Q) used in the case under consideration with regard to the cooling times t8/5 and processing using GMAW thick-wire welding. It was reproducibly and economically possible to place the failure location of the welded high-strength component outside the weld seam and the heat-affected zone. Publication: 2021 Authors: Prof. Dr.-Ing. Hensel, Dr.-Ing. M. Kusch, Dr.-Ing. A. Hälsig, ]}, M. Sc. J. Kimme

P 1314 - Space-forming load-bearing structures made of sandwich elements In addition to their outstanding space-enclosing function and thermal insulation properties, (steel) sandwich elements have load-bearing properties that allow loads to be transferred in and out of their plane. Single-storey buildings, such as small warehouses, petrol station shops and car washes, can therefore only be built with sandwich elements without additional load-bearing frame substructures. There is a lack of verification methods, in particular for load transfer, which would enable this economical construction method. The aim of the research project was to validate existing calculation approaches for load-bearing and serviceability and the detailed solutions for load transfer and distribution by means of experimental investigations and, if necessary, to develop them further. The knowledge gained from the holistic consideration of the construction method should then serve as a basis for the acquisition of a building authority approval. To achieve these goals, a self-supporting construction made of sandwich elements was first designed as an example object. For this purpose, all necessary construction drawings and detailed solutions for the formation of the load application points and joints were worked out and defined for this application. Experimental investigations into the load-bearing behaviour of a self-supporting construction made of sandwich elements were carried out using a test matrix defined in the research proposal. The extensive local and global axial compression tests were carried out on test specimens, taking into account a practical and application-related design of the load application points. The deformations and maximum loads were measured. The measured loads were then statistically evaluated and the actual local and global load-bearing capacity as well as the failure behaviour of the self-supporting construction made of sandwich elements were analysed. The analytically determined ultimate loads in the ultimate and serviceability limit states were used as a reference. It was found that the experimentally determined loads were far higher than the analytically calculated values. This showed that the design of the structure with the existing design approaches provides conservative results and is therefore on the safe side. The design of the load introduction structure for uplifting forces could also be ensured using a presented design approach. In order to ensure a holistic view of the construction, an economic and ecological analysis of the construction method was carried out. In the economic analysis, it was shown that self-supporting constructions made of sandwich elements without a steel substructure save approx. 9% of the investment costs and approx. 10% of the heating costs. The life cycle assessment also showed that the construction method results in emission and energy savings and is more environmentally friendly. Overall, the research report provides a sound scientific and technical basis for the design, construction and dimensioning of self-supporting structures made of sandwich elements, as well as the necessary test results and analyses for obtaining building authority approval. Publication: September 2022 Authors: Univ.-Prof. Dr.-Ing. D. Ungermann, M.Sc. G. A. Eseme