P 46 - Investigation of the load-bearing behaviour of racking structures under specified load constellations (design rules)

P 11 - Investigations on connections of closed and open profiles made of high-strength steels Extensive theoretical and practical investigations in Germany and abroad over the last 15 years have shown that the load-bearing behaviour of hollow section structures cannot be described or calculated without further ado. The special problem of such constructions lies in the area of the connections and joints. Inhomogeneous stress states are effective in these node areas, which cannot be analysed using the elementary calculation approaches commonly used in steel construction. Instead, a differentiated approach is required. Intensive attention has been paid to this issue in recent years as part of various research programmes. An important result of this work is the draft standard DIN 18 808 ("Steel structures, structures made of hollow sections under predominantly static loading"), which describes the use of essential structural shapes of hollow sections made of St 37 and St 52 under predominantly static loading. The applicability of the DIN 18 808 standard to hollow section constructions made of high-strength fine-grain structural steels St E 460 and St E 690, as well as combinations of hollow sections with open rolled sections, was investigated for the first time as part of the present research programme in Karlsruhe. Connecting tests were also carried out on flat specimens in order to enable a relation to the DASt-Rioll, which is now available. In this programme, the vibration behaviour of cut edges and prestressed bonded connections in high-strength steel grades was also investigated. The component tests carried out on the various design forms, such as K-joints, T-joints, L-joints (i.e. rigid frame corners) and end plate connections, were intended to demonstrate for the first time the possible, fundamentally sensible application of these materials and also to clarify the orientation possibilities in accordance with the regulations of DIN 18 808. Due to the limited profile dimensions available, this could only be done in certain dimension ranges. As part of a research programme (P 71), again financially supported by the Arbeitsgemeinschaft Industieller Forschungsvereinigungen e.V. (AIF) and supervised by the Studiengesellschaft für Anwendungstechnik von Eisen und; Stahl e. V., additional static and dynamic tests were carried out with flat specimens and with nodal points made from hollow sections of the materials StE 460 and StE 690. In this respect, there is a direct connection between the present report and the final report on P 71 of the Studiengesellschaft. STUDIENGESELLSCHAFT FÜR ANWENDUNGSTECHNIK VON EISEN UND STAHL e.V. Publication: 1982 Authors: Prof. Dr.-Ing. F. Mang, Dipl.-Ing. Ö. Bucak, Dipl.-Ing. G. Steidl

P 08.1 - Load-bearing behaviour of steel columns in combination with concrete (hollow sections) This paper contains the calculation and design of concrete-lined hollow section columns made of structural steel under compression and uniaxial bending. After a brief introduction, Section 2 summarises international research work in this field. In Section 3, a calculation programme is developed as an accurate numerical method. Section 4 contains interaction relations for the ultimate limit state for the whole range between centric compression and pure bending. Many results obtained with the described calculation programme and the interaction curves are compared with each other and with available test results; very good agreement can almost always be observed. Publication: 1975 Authors: Prof. Dr.-Ing. Roik, R. Bergmann, H. Bode, G. Wagenknecht

P 08.2 - Load-bearing behaviour of steel columns in combination with concrete (open profiles) This paper contains the calculation and design of steel columns in concrete under compression and uniaxial bending. Some comments and design suggestions are also made for biaxial bending. Section 2 summarises international research work. Section 3 explains a calculation programme that is used for precise numerical calculation. Section 4 contains interaction relations and design proposals based on the European buckling stress curves. The proposed design procedure is explained using a number of examples. Numerous ultimate loads determined in accordance with Sections 3 and 4 are compared with foreign test results. A generally good agreement can be established Publication: 1976 Authors: J. Stanke

P 08.4 - Analysis of the actual state of the material properties as a function of the material and processing (forging, rolling) quality of thick-walled profiles and solid profiles Publication: 1977 Authors: Prof. Dr.-Ing. P. Funke