P 1253 - Building-integrated solar steel sandwich elements with mineral wool core for industrial and commercial construction

P 1254 - Investigation into the correct representation of the heat transmission of lightweight steel constructions in relevant standards for the construction industry Transmission heat losses (HT) and ventilation heat losses (HV) are essential for calculating the heating energy demand of a building. In calculations with constant boundary conditions, the transmission heat loss is made up of the heat losses through flat components (U-values and associated component areas) of the entire heat-exchanging enveloping surface (Ages) and through thermal bridges. Depending on the boundary conditions, correction values (Fx) are also introduced, which serve to apply suitable reductions in heat loss via an annual balance for those components that are not adjacent to the outside air. These are, for example, basement rooms or top storey ceilings that adjoin an unheated roof space. In addition, reductions in heat loss due to solar irradiation are also usually applied to opaque building components using annual or monthly balancing. This is based on the familiar formulae for heat transport through building components, which apply to static, i.e. unchanging, boundary conditions. This also includes the unchanging internal and external thermal resistance (Rsi and Rse). For today's standard verifications based on static boundary conditions, the transmission heat loss for the entire building HT is calculated using the U-value equation and a flat-rate or detailed method for the thermal bridge allowance ΔUWB. From this, a heat quantity QT is calculated for each month - with monthly constant approximate temperature differences between indoor and outdoor air (inside - outside). The sum of all monthly QT is used to calculate the amount of heat emitted by a building through transmission for the entire year, which then has to be balanced out by a heating system. In addition to the heating energy requirement, the cooling energy requirement is also calculated in a similar way with constant monthly boundary conditions. In both cases, solar gains through transparent building components, heat gains through internal loads and ventilation heat losses are included in the balance. In this case, the excessive energy input is compensated for by a system to dissipate the heat. This brief study examines the way in which buildings in lightweight metal constructions can suffer certain disadvantages with regard to transmission heat losses in the static calculation methods due to the fact that higher heat losses may occur in these largely approximate calculation methods compared to more precise transient calculation methods. The usefulness of this approach is also emphasised by high-resolution measurements from previous studies (FOSTA research project P779 [FOS14a]). Publication: 2017 Authors: R. Koschade, Dipl.-Vw. D. Greiner, Dipl.-Ing. R. Koschade

P 1255 - EcoWeldSafe- Required weld seam qualities for compliance with the safety standard for steel structures subject to alternating loads The project Required weld seam quality for compliance with the safety standard for steel structures subject to alternating stresses deals with the evaluation of optimised weld seam designs. The aim of the research project is to comply with and verify the existing safety standard of welded, alternately stressed steel structures using simplified manufacturing processes and types of execution and to develop and verify design approaches for the associated types of execution and execution qualities. In this project, the occurring irregularities of weld seam designs, which are sought by the industry for technical and economic reasons, are analysed and their influence on the fatigue strength of the steel structures is determined. The focus is on root notch, insufficient weld penetration, penetration notch and misalignment. Based on the analyses, new notch classes are defined depending on the irregularities that occur. In addition, the achievable weld seam quality and the associated fatigue strength are determined for specific execution methods. Based on the fatigue strength values for various production imperfections determined in the project, the application limits of the applicable standard values are to be checked and the mathematical methods adapted if necessary. In addition to the efficient nominal and structural stress concepts, findings from the local notch stress concept are also taken into account. The result is a proposal for a verification procedure based on nominal and notch stress concepts. This will be presented to the committees for discussion. These project results will enable steel construction companies to design in a resource-saving manner with lower production costs than before and demonstrably comply with the required safety standard. Labour-intensive work can be reduced, as reworking is no longer necessary due to the high demands on the quality of the weld seams. Steel construction companies (primarily SMEs) and related branches of industry achieve clear competitive advantages both nationally and internationally. Publication: 2021 Authors: Prof. Dr.-Ing. Engelhardt, Prof. Dr.-Ing. K. Rother

P 1256 - Extension of the processing spectrum of laser-welded components in the powertrain through the use of dynamic beam deflection and reduced ambient pressure Modern solid-state lasers offer numerous advantages for joining tasks in vehicle construction and particularly in transmission technology due to their high beam quality, energy efficiency, availability and more flexible beam guidance. At the same time, however, the high beam qualities and small focus diameters place higher demands on the production and positioning accuracy of the components to be joined. The overall aim of the research project is therefore to extend the application limits of laser beam welding with solid-state lasers by increasing the process stability to compensate for production-related tolerances for use in gear manufacturing. The research project is based on the working hypothesis that the use of beam oscillation in combination with reduced ambient pressure in laser beam welding with solid-state lasers leads to a significant improvement in gap-bridging capability while simultaneously achieving high seam quality. Using the case-hardening steel 1.7131 as an example, the influence of reduced ambient pressure on the resulting gap-bridging properties is first analysed. Furthermore, the evaluation of suitable oscillation figures and their influence on the process limits with regard to an improvement in gap bridging is carried out. Based on the fundamental investigations, the effects of the gap bridging properties on the joint strength, the process transfer to axial welds and the welding processing of quenched and tempered steel are analysed. The main influencing factor on gap bridging in laser beam welding has turned out to be the weld seam width resulting from the process. A reduced ambient pressure, due to the generally narrower seam geometry, leads on the one hand to a decrease in gap bridging. On the other hand, the reduced ambient pressure causes a decrease in weld spatter formation and thus an increase in process quality, especially for the production of transmission components. To extend the process limits for bridging joining gaps, it is advisable to widen the weld seam geometry so that more material is melted on the seam flanks and is available for gap filling. This can be achieved by positive defocussing of the laser beam and line oscillation transverse to the welding direction. As a result of the wider molten zone, a lower cover layer undercamber with a flatter seam flank angle is formed. The transfer of results to the welding processing of heat-treatable steel also revealed a positive influence of the reduced ambient pressure on the weld-induced crack formation, which thus contributes to increased process reliability and an expansion of the processing spectrum for laser beam welding of difficult-to-weld materials. Publication: 2021 Authors: Prof. Dr.-Ing. K. Dilger

P 1259 - Influences on delayed cold cracking and determination of the minimum waiting time before testing welded joints made of fine-grained structural steel The central challenge for the future is to reduce greenhouse gas emissions by 55% by 2030 compared to 1990, in particular by reducing CO2 emissions and phasing out coal-fired power generation. This poses major challenges for primary energy production, which can only be met with renewable energy. Due to large and consistent energy yields, energy from offshore wind turbines (OWA) will play a decisive role in realising this goal. In addition to pure electricity generation, these will also be used to produce other alternative energy sources, such as green hydrogen. The regulations on which welding production is based contain blanket specifications on the minimum waiting time (MWT) of up to 48 hours before non-destructive testing (NDT) of the weld seams may take place. Compliance with these MWTs leads to considerable financial burdens in the production of OWA. Modern thermomechanically rolled (offshore) steels have a lower carbon equivalent and therefore improved weldability. These steels are currently available with strengths of up to 500 MPa and can be processed without preheating and with low heat input without cracking. Waiting times of days until NDT can therefore only be justified to a limited extent and require further clarification. The aim of the research is therefore to develop findings to optimise the minimum waiting times until non-destructive testing of weld seams for steels with yield strengths of 500 MPa. In order to achieve this, welds were carried out under variation of hydrogen content and constructive shrinkage restraint (degree of clamping) and examined with regard to the time until the occurrence of delayed cracks by means of acoustic emission testing or phased array ultrasonic testing. Supported by numerical simulations, further influencing factors (e.g. heat conduction) and their influence on the formation of cold cracks were analysed using validated models. The investigations have shown that the steels used here can be processed without cracking under controlled environmental conditions and with appropriate welding technology. In the welding tests carried out, material damage occurred primarily when the hydrogen-containing shielding gas was used. In addition, it was found for all welding tests that the multi-layer technique in the materials used here had a positive effect on reducing the hydrogen concentration and that this was already significantly reduced after cooling to room temperature. In terms of hydrogen concentration, this has a positive effect on the prevention of hydrogen-assisted cold cracking. The study also showed that both experimental and numerical methods must be combined to optimise the minimum waiting times until the non-destructive testing of the weld seams. Publication: 2021 Authors: Prof. Dr.-Ing. habil. T. Böllinghaus